忻府輪椅稱*安澤稱重模塊工廠

　　(2)避免電子吊秤受劇烈扳動和碰撞

　　電子吊秤內部許多電子元器件，如集成電路、石英晶體、傳感器、顯示器等，當電子吊秤受到劇烈碰撞時，可能會損壞這些元器件，造成電子秤故障，影響準確度以致影響正常使用，要避免秤體和其他物品碰撞或從高空中摔下，儀表要輕拿輕放，不要隨意放置，以防不必要的損失，儀表固定在起重機上使用時要采取減振措施，以免影響可靠性。

　　(3)不得隨意拆卻電子吊秤上的零部件

　　在電子吊秤正常使用時，不要隨意拆卸電子秤上的零部件，更不要打開傳感器上的密封口，拆卸儀表上的集成電路等元器件，必要的維修，必須在有關技術人員指導下或具備一定的維修知識后進行，以防故障擴大。

忻府輪椅稱*安澤稱重模塊工廠

電子吊秤

科技名詞定義

中文名稱：電子吊秤

英文名稱：electronic hoist scale

定義：能自動檢測和顯示所吊物料質量和超載報警的裝置。

電子吊秤的基本參數有準確度等級、檢定分度值e、zui大稱量（Max）、zui小稱量（Min）和工作級別。

檢定分度值e 　　

e=d,d為實際分度值。 　　

檢定分度值e以含質量單位的下列數字之一表示： 　　

1×10k.2×10k.5×10k(k為正整數、負整數或零)

稱量結果間的允許誤差 　　

不管稱量結果如何變化，任何一次稱量結果的誤差，應不大于該稱量的zui大允許誤差。

電子吊秤的重復性 　　

對同一載荷，多次稱重結果之差，應不大于該稱量的zui大允許誤差的值。

忻府輪椅稱*安澤稱重模塊工廠地磅的常見故障及維修保養：故障現象：用地磅過磅時，司磅人員發現不能正常稱重，時而有數據時而出現欠載無數據的情況，一次儀表稱重數字下閃爍“LC稱重偏高/偏低（7、8、10）”，數字還跳變閃爍不穩定。根據故障現象，進行原因分析：  1、儀表因無良好且單獨的接地線而引起的靜電干擾或無線電射頻干擾。  2、無配置穩壓電源而造成的電壓不穩或風力過大造成儀表顯示不穩。  3、信號線接線端子松動、焊點虛焊或氧化，電纜因老鼠咬破或磨損而造成不良。  4、接線盒有水汽或接線板受潮而導致絕緣電阻下降、輸出信號時大時小不穩定。  5、傳感器漂移或損壞、傳感器信號線與屏蔽層間短接或絕緣性能下降。  6、儀表開機預熱時間不夠或儀表損壞，儀表傳感器連接頭氧化或接觸不良。  7、地基松動、秤臺與基礎出現雜物堵塞、限位螺栓與基礎無間隙等。故障處理：  因為一次儀表閃爍提示的內容是7、8、10號傳感器輸出異常，故查看7、8、10號傳感器，從稱量傳感器的外觀及傳輸線和接地線看無明顯損傷或接觸不良虛焊等情況； （2）查看秤體限位螺栓，發現其滿足技術要求；（3）根據傳感器排列方式7、8、10號傳感器信號電纜應在同一個（即3#）接線盒內，又因頭一天剛剛下過大雨，故懷疑3#接線盒受潮，打開接線盒，發現接線盒已進水，用吹風機將其吹干，酒精棉球把接線盒擦干凈再重新開機觀察，發現稱重儀表已恢復正常，接下來用叉車進行偏載試驗，后用重砝碼車進行量程校準。  利用叉車進行偏載試驗，我們使用的地磅有10只傳感器。分別在每個傳感受器位置上方進行壓點。試驗結果如下，見表一  在測試中選用的叉車事先在50t地磅上進行了稱量重5000Kg，然后到該汽車衡上進行偏載驗證，稱量結果*。進行重復性試驗：選一臺重車，多次上秤進行稱量。所得結果不大于該稱量大允許誤差的值，判定該秤重復性試驗合格

忻府輪椅稱*安澤稱重模塊工廠