巴宜3T吊秤*米林2噸吊秤*標簽打印叉車秤

防爆磅秤維修故障解決方案：

（1）稱重物移除后無法回到零點的故障分析檢查傳感器輸出信號值是否于標準內（A/D的總放大碼/使用內碼范圍/底碼范圍），如果信號值未在標準內，調節傳感器可調電阻，將信號值調到標準內，如無法補償請檢查傳感器是否有問題，在保證傳感器輸出正常（秤體穩定）情況下，鎖定儀表故障，一般是放大電路及A/D轉換電路發生問題，再依據電路原理逐一判斷測試分析，以zui終解決問題。（2）稱量不準確的故障分析觀測內碼值是否穩定，傳感器各部位是否有摩擦現象，穩壓電源是否穩定，運放電路是否正常，使用砝碼測試秤盤四腳秤量是否平均。依照說明書指示，進一步做儀表局部分析或重量校正。（3）無法開機的故障先確定非保險絲、電源開關、電源線及電壓切換開關的問題所造成，檢查變壓器有無交流電壓輸入及交流電輸出。如果儀表帶有電池將電池取下再以AC電源開機，以了解是否為電池電壓不足所造成。其次再檢測整流電路、穩壓電路以及顯示驅動電路是否出現異常，如果這些都沒問題檢查處理器及附屬電路是否燒壞。巴宜3T吊秤*米林2噸吊秤*標簽打印叉車秤

（4）顯示亂碼將原來的顯示電路拆下，換一個正常的顯示電路看是否正常。如果顯示正常說明顯示電路出現問題，如果不正常，應檢查驅動電路是否有故障，zui后檢查處理器顯示輸出的引腳是否在合理的輸出范圍。（5）按鍵不好用先更換新按鍵進行測試，如新按鍵功能正常時，則可判定為按鍵接觸不良，測量按鍵與CPU之間線路有無斷路、虛焊。檢查按鍵支座是否有接觸不良現象。測量按鍵與CPU回路上的二極管、電阻等是否有短路、斷路的情況。（6）無法稱到滿載和無法回零的情況差不多，多數可能由于小信號輸入范圍發生了改變。按照無法回零的方法檢測，如果找不出問題，就先檢測供電電源、A/D電路是否正常，再檢測傳感器輸出。（7）傳感器故障判別方法①靜態測量法：使用萬用電表之歐姆檔，分別量測傳感器之E+對S+、S-（或是E-對S+、S-也可）阻值是否相同，一般而言誤差在0.5Ω以上就需做補償，如誤差過大（2Ω以上）則建議更換傳感器。②動態測量法：將傳感器接線正確的接回主機板，使用數位電表（四位半以上較佳）之DCV檔上，量測S+對地與S-對地之電壓是否相等（是*），如不相等需做傳感器補償。（8）傳感器補償傳感器輸出信號過高請加一電阻器在傳感器的“E+S-”之間使信號值到正常范圍（電阻值越低，傳感器輸出信號越低）。傳感器輸出信號過低或-ERR請加一電阻器在傳感器的“E+~S+”之間使信號值到正常范圍（電阻值越低，傳感器輸出信號越高）。檢測A/D電路放大碼的方法把電子秤調試到內部設定狀態（使之顯示當前的內碼狀態）施加滿稱量砝碼，記錄此放大碼值，它們的關系：底碼值+滿稱量放大碼+安全區碼。

巴宜3T吊秤*米林2噸吊秤*標簽打印叉車秤