防爆電子臺秤防爆電子桌秤隔爆電子臺秤防腐蝕電子秤維修:
1、開機無任何顯示、聲音：從電路上分析“無顯示”是顯示電路的故障，沒有聲音是蜂鳴電路上的故障。這2個故障同時出現的概率很低。所以一般故障出現在供電電路上。
2、稱重量不準：觀測傳感器各部位是否有摩擦現象，穩壓電源是否穩定，運放電路是否正常。A/D電路的線路板是否有異物。
3、顯示不良：開機觀察正常的LCD上是否有不良情況，如果沒有的話可斷定為LCD不良；檢查CPU接腳有無氧化、冷焊或短路現象；檢查CPU與LCD之間線路有無短路。
4、電池無法蓄電：先確定保險絲、電源開關、電源線的問題所造成；檢查變壓器有無AC110/220輸入及AC18V輸出；檢查機版，變壓器輸入端插PIN附件之二極體是否正常；更換蓄電池。
5、電子稱無法充電或充電指示燈不量或沒反應：請先確定電子稱的110V/220V電壓切換開關是否調到與使用電源一樣的電壓，并確定充電線已牢固的插在秤上的充電座；檢查充電線是否有外力因素而造成斷路；檢查保險絲是否不良；蓄電池不良。
6、按鍵無動作或動作不正常會自動觸發：按鍵不良；按鍵插座不良。
7、電子稱無法秤到滿載：電子稱保護螺絲未拆除；電子稱是否有異物滲入造成干涉或撞擊、摔傷；電子臺秤的內部程序設定是否正確。
防爆電子臺秤防爆電子桌秤隔爆電子臺秤防腐蝕電子秤維修:
021-51087563
